[hylafax-users] faxgetty:problems with multipage documents and sedlbauer speedfax pci class 1

To: "hylafax-users@hylafax.org" <hylafax-users@hylafax.org>
Subject: [hylafax-users] faxgetty:problems with multipage documents and sedlbauer speedfax pci class 1
From: "Detlev Bonkamp" <detlev@bonkamp.de>
Reply-To: "Detlev Bonkamp" <detlev@bonkamp.de>
Date: Wed, 08 May 2002 11:43:06 +0200
Hello,

i have some problems using Hylafax 4.1.2 with my Sedlbauer speedfax pci ISDN-Card. The speedfax pci is a semi-active ISDN-CArd which acts as a Class 1 
Modem.

Receiving one Fax page wether in fine or in normal resolution works fine but multipage faxes will abort after the first page.

Has anyone any idea ?

Thanks for help, 
Detlev.

Here are some cuts from the syslog


****************Fax-Init

May  8 10:56:52 comsurv FaxQueuer[13745]: MODEM ttyI1: NUMBER xxx
May  8 10:56:52 comsurv FaxGetty[13758]: OPEN /dev/ttyI1  HylaFAX (tm) Version 4
.1.2
May  8 10:56:52 comsurv FaxGetty[13758]: MODEM set DTR OFF
May  8 10:56:52 comsurv FaxGetty[13758]: DELAY 75 ms
May  8 10:56:52 comsurv FaxGetty[13758]: MODEM set DTR ON
May  8 10:56:52 comsurv FaxGetty[13758]: DELAY 2600 ms
May  8 10:56:55 comsurv FaxGetty[13758]: MODEM set baud rate: 19200 baud, input
flow XON/XOFF, output flow XON/XOFF
May  8 10:56:55 comsurv FaxGetty[13758]: MODEM flush i/o
May  8 10:56:55 comsurv FaxGetty[13758]: <-- [4:ATZ\r]
May  8 10:56:55 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:55 comsurv FaxGetty[13758]: DELAY 3000 ms
May  8 10:56:58 comsurv FaxGetty[13758]: <-- [7:at&e71\r]
May  8 10:56:58 comsurv FaxGetty[13758]: --> [6:at&e71]
May  8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:58 comsurv FaxGetty[13758]: <-- [5:ATE0\r]
May  8 10:56:58 comsurv FaxGetty[13758]: --> [4:ATE0]
May  8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:58 comsurv FaxGetty[13758]: <-- [5:ATV1\r]
May  8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:58 comsurv FaxGetty[13758]: <-- [5:ATQ0\r]
May  8 10:56:58 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:58 comsurv FaxGetty[13758]: <-- [7:ATS0=0\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [7:ATS8=2\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [8:ATS7=60\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [12:AT+FCLASS=?\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [5:0,1,8]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports "Data"
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports "Class 1"
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports "Voice"
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [12:AT+FCLASS=1\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [5:ATI3\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [10:Linux ISDN]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [1:0]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM: Mfr Linux ISDN 0
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [5:ATI0\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [10:Linux ISDN]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM: Model Linux ISDN
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [9:AT+FTM=?\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [13:3,24,48,72,96]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 3.85 line/mm
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 7.7 line/mm
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 2400 bit/s
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 4800 bit/s
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 7200 bit/s
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 9600 bit/s
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports page width 1728 pixels i
n 215 mm
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports page width 2048 pixels i
n 255 mm
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports page width 2432 pixels i
n 303 mm
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports A4 page length (297 mm)
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports B4 page length (364 mm)
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports unlimited page length
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 1-D MR
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 2-D MR
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 0 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 5 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 10 ms, 5 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 10 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 20 ms, 10 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 20 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 40 ms, 20 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: MODEM Supports 40 ms/scanline
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [9:AT+FRM=?\r]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [13:3,24,48,72,96]
May  8 10:56:59 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:56:59 comsurv FaxGetty[13758]: <-- [12:AT+FCLASS=1\r]
May  8 10:57:00 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:57:00 comsurv FaxGetty[13758]: MODEM LINUX ISDN 0 Linux ISDN/
May  8 10:57:00 comsurv FaxGetty[13758]: <-- [5:ATM0\r]
May  8 10:57:00 comsurv FaxGetty[13758]: --> [2:OK]
May  8 10:57:00 comsurv FaxGetty[13758]: STATE CHANGE: BASE -> RUNNING
May  8 10:57:00 comsurv FaxGetty[13758]: MODEM input buffering disabled
May  8 10:57:00 comsurv FaxQueuer[13745]: MODEM ttyI1: READY, capabilities P3fc3
e73f:ff


*************** receiving page fax, normal resolutuio
May  8 11:26:52 comsurv FaxGetty[13908]: --> [17:CALLER NUMBER: 26]
May  8 11:26:52 comsurv FaxGetty[13908]: --> [4:RING]
May  8 11:26:52 comsurv FaxGetty[13908]: ANSWER: CID NUMBER "CALLER NUMBER: 26"
NAME "CALLER NUMBER: 26"
May  8 11:26:52 comsurv FaxGetty[13908]: STATE CHANGE: LISTENING -> ANSWERING
May  8 11:26:52 comsurv FaxGetty[13908]: MODEM input buffering enabled
May  8 11:26:52 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID 00000009
May  8 11:26:57 comsurv FaxGetty[13908]: ANSWER: FAX CONNECTION  DEVICE '/dev/tt
yI1'
May  8 11:27:02 comsurv FaxGetty[13908]: ACCEPT TSI "+49 2534 xxxx"
May  8 11:27:57 comsurv FaxGetty[13908]: RECV FAX (00000009): from +49 2534 xxxxx
2, page 1 in 0:55, INF, 3.85 line/mm, 1-D MR, 9600 bit/s
May  8 11:28:00 comsurv FaxGetty[13908]: RECV FAX (00000009): recvq/fax00006.tif
 from +49 2534 xxxxx, route to <unspecified>, 1 pages in 1:03
May  8 11:28:02 comsurv FaxGetty[13908]: RECV FAX (00000009): session with +49 2
534 xxxxx terminated abnormally: T.30 T2 timeout, expected page not received
May  8 11:28:02 comsurv FaxGetty[13908]: RECV FAX: bin/faxrcvd "recvq/fax00006.t
if" "ttyI1" "00000009" "T.30 T2 timeout, expected page not received" "CALLER NUM
BER: 26" "CALLER NUMBER: 26"
May  8 11:28:02 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID
May  8 11:28:02 comsurv FaxGetty[13908]: <-- [5:ATH0\r]
May  8 11:28:02 comsurv scanmails[13936]: execution started
May  8 11:28:02 comsurv FaxGetty[13908]: --> [10:NO CARRIER]
May  8 11:28:02 comsurv FaxGetty[13908]: MODEM No carrier
May  8 11:28:02 comsurv FaxGetty[13908]: MODEM set DTR OFF
May  8 11:28:02 comsurv FaxGetty[13908]: MODEM set DTR OFF
May  8 11:28:02 comsurv FaxGetty[13908]: DELAY 75 ms
May  8 11:28:02 comsurv FaxGetty[13908]: MODEM set DTR ON
May  8 11:28:02 comsurv FaxGetty[13908]: DELAY 2600 ms
May  8 11:28:03 comsurv scanmails[14053]: terminating
May  8 11:28:05 comsurv FaxGetty[13908]: MODEM set baud rate: 19200 baud, input
flow XON/XOFF, output flow XON/XOFF
May  8 11:28:05 comsurv FaxGetty[13908]: MODEM flush i/o
May  8 11:28:05 comsurv FaxGetty[13908]: <-- [4:ATZ\r]
.....

and the ../hylafax/log-file

May 08 11:26:52.15: [13908]: SESSION BEGIN 00000009 492534xxxxxx
May 08 11:26:52.15: [13908]: HylaFAX (tm) Version 4.1.2
May 08 11:26:52.15: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output dis
abled
May 08 11:26:52.15: [13908]: <-- [4:ATA\r]
May 08 11:26:57.29: [13908]: --> [7:CONNECT]
May 08 11:26:57.29: [13908]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyI1'
May 08 11:26:57.29: [13908]: STATE CHANGE: ANSWERING -> RECEIVING
May 08 11:26:57.29: [13908]: MODEM input buffering enabled
May 08 11:26:57.29: [13908]: RECV FAX: begin
May 08 11:26:57.29: [13908]: MODEM input buffering disabled
May 08 11:26:57.29: [13908]: <-- HDLC<23:FF C0 02 0E B6 86 D6 76 F6 42 04 04 04
04 04 04 04 04 04 04 04 04 04>
May 08 11:26:57.29: [13908]: <-- data [23]
May 08 11:26:57.29: [13908]: <-- data [2]
May 08 11:26:57.33: [13908]: --> [7:CONNECT]
May 08 11:26:57.33: [13908]: <-- HDLC<10:FF C8 01 00 73 5F 01 79 03 C0>
May 08 11:26:57.33: [13908]: <-- data [10]
May 08 11:26:57.33: [13908]: <-- data [2]
May 08 11:26:58.45: [13908]: --> [2:OK]
May 08 11:26:58.45: [13908]: <-- [9:AT+FRH=3\r]
May 08 11:26:58.72: [13908]: --> [7:CONNECT]
May 08 11:27:00.36: [13908]: --> HDLC<25:FF C0 C2 4C EC 4C AC 6C 04 2C CC AC 4C
04 9C 2C D4 04 04 04 04 04 04 FA C4>
May 08 11:27:00.36: [13908]: --> [2:OK]
May 08 11:27:00.36: [13908]: REMOTE TSI "+49 2534 xxxxx"
May 08 11:27:00.36: [13908]: <-- [9:AT+FRH=3\r]
May 08 11:27:00.37: [13908]: --> [7:CONNECT]
May 08 11:27:00.68: [13908]: --> HDLC<11:FF C8 C1 00 60 15 01 01 00 0A 70>
May 08 11:27:00.68: [13908]: --> [2:OK]
May 08 11:27:00.68: [13908]: REMOTE wants 9600 bit/s
May 08 11:27:00.68: [13908]: REMOTE wants page width 1728 pixels in 215 mm
May 08 11:27:00.68: [13908]: REMOTE wants unlimited page length
May 08 11:27:00.68: [13908]: REMOTE wants 3.85 line/mm
May 08 11:27:00.68: [13908]: REMOTE wants 1-D MR
May 08 11:27:00.68: [13908]: RECV training at v.29 9600 bit/s
May 08 11:27:00.68: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output gen
erated
May 08 11:27:00.68: [13908]: <-- [10:AT+FRM=96\r]
May 08 11:27:01.04: [13908]: --> [7:CONNECT]
May 08 11:27:02.63: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis
abled
May 08 11:27:02.63: [13908]: RECV: TCF 1915 bytes, 5% non-zero, 1809 zero-run
May 08 11:27:02.63: [13908]: --> [10:NO CARRIER]
May 08 11:27:02.63: [13908]: DELAY 75 ms
May 08 11:27:02.71: [13908]: TRAINING succeeded
May 08 11:27:02.71: [13908]: ACCEPT TSI "+49 2534 xxxxx"
May 08 11:27:02.71: [13908]: <-- [9:AT+FTH=3\r]
May 08 11:27:04.34: [13908]: --> [7:CONNECT]
May 08 11:27:04.34: [13908]: <-- HDLC<3:FF C8 21>
May 08 11:27:04.34: [13908]: <-- data [3]
May 08 11:27:04.34: [13908]: <-- data [2]
May 08 11:27:04.60: [13908]: --> [2:OK]
May 08 11:27:04.60: [13908]: MODEM input buffering enabled
May 08 11:27:04.60: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen
erated
May 08 11:27:04.60: [13908]: <-- [10:AT+FRM=96\r]
May 08 11:27:05.19: [13908]: --> [7:CONNECT]
May 08 11:27:05.19: [13908]: RECV: begin page
May 08 11:27:55.94: [13908]: RECV: 1149 total lines, 0 bad lines, 0 consecutive
bad lines
May 08 11:27:55.94: [13908]: RECV: end page
May 08 11:27:55.94: [13908]: --> [10:NO CARRIER]
May 08 11:27:55.94: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis
abled
May 08 11:27:55.94: [13908]: MODEM input buffering disabled
May 08 11:27:55.94: [13908]: <-- [9:AT+FRH=3\r]
May 08 11:27:55.98: [13908]: --> [7:CONNECT]
May 08 11:27:57.05: [13908]: --> HDLC<5:FF C8 F2 AC A0>
May 08 11:27:57.05: [13908]: --> [2:OK]
May 08 11:27:57.05: [13908]: RECV recv MPS (more pages, same document)
May 08 11:27:57.05: [13908]: DELAY 75 ms
May 08 11:27:57.13: [13908]: <-- [9:AT+FTH=3\r]
May 08 11:27:57.13: [13908]: --> [10:NO CARRIER]
May 08 11:27:57.13: [13908]: RECV send MCF (message confirmation)
May 08 11:27:57.13: [13908]: RECV FAX (00000009): from +49 2534 xxxxx, page 1 in
 0:55, INF, 3.85 line/mm, 1-D MR, 9600 bit/s
May 08 11:27:57.13: [13908]: MODEM input buffering enabled
May 08 11:27:57.13: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen
erated
May 08 11:27:57.13: [13908]: <-- [10:AT+FRM=96\r]
May 08 11:28:00.75: [13908]: --> [7:FCERROR]
May 08 11:28:00.75: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis
abled
May 08 11:28:00.75: [13908]: MODEM input buffering disabled
May 08 11:28:00.75: [13908]: RECV FAX (00000009): recvq/fax00006.tif from +49 25
34 xxxxx, route to <unspecified>, 1 pages in 1:03
May 08 11:28:00.75: [13908]: RECV FAX: T.30 T2 timeout, expected page not receiv
ed
May 08 11:28:00.75: [13908]: <-- [9:AT+FTH=3\r]
May 08 11:28:02.38: [13908]: --> [7:CONNECT]
May 08 11:28:02.38: [13908]: <-- HDLC<3:FF C8 5F>
May 08 11:28:02.38: [13908]: <-- data [3]
May 08 11:28:02.38: [13908]: <-- data [2]
May 08 11:28:02.64: [13908]: --> [2:OK]
May 08 11:28:02.64: [13908]: MODEM input buffering enabled
May 08 11:28:02.64: [13908]: RECV FAX (00000009): session with +49 2534 xxxxx te
rminated abnormally: T.30 T2 timeout, expected page not received
May 08 11:28:02.64: [13908]: RECV FAX: bin/faxrcvd "recvq/fax00006.tif" "ttyI1"
"00000009" "T.30 T2 timeout, expected page not received" "CALLER NUMBER: 26" "CA
LLER NUMBER: 26"
May 08 11:28:02.71: [13908]: RECV FAX: end
May 08 11:28:02.71: [13908]: SESSION END

************ the same with fine resolution

May  8 11:31:52 comsurv FaxGetty[13908]: --> [17:CALLER NUMBER: 26]
May  8 11:31:52 comsurv FaxGetty[13908]: --> [4:RING]
May  8 11:31:52 comsurv FaxGetty[13908]: ANSWER: CID NUMBER "CALLER NUMBER: 26" NAME "CALLER NUMBER: 26"
May  8 11:31:52 comsurv FaxGetty[13908]: STATE CHANGE: LISTENING -> ANSWERING
May  8 11:31:52 comsurv FaxGetty[13908]: MODEM input buffering enabled
May  8 11:31:52 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID 00000010
May  8 11:31:57 comsurv FaxGetty[13908]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyI1'
May  8 11:32:03 comsurv FaxGetty[13908]: ACCEPT TSI "+49 2534 xxxxx"
May  8 11:33:21 comsurv FaxGetty[13908]: RECV FAX (00000010): from +49 2534 xxxxx, page 1 in 1:18, INF, 7.7 line/mm, 1-D MR, 9600 bit/s
May  8 11:33:25 comsurv FaxGetty[13908]: RECV FAX (00000010): recvq/fax00007.tif from +49 2534 xxxxx, route to <unspecified>, 1 pages in 1:28
May  8 11:33:26 comsurv FaxGetty[13908]: RECV FAX (00000010): session with +49 2534 xxxxx terminated abnormally: T.30 T2 timeout, expected page 
not received
May  8 11:33:26 comsurv FaxGetty[13908]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif" "ttyI1" "00000010" "T.30 T2 timeout, expected page not 
received" "CALLER NUMBER: 26" "CALLER NUMBER: 26"
May  8 11:33:27 comsurv FaxQueuer[13745]: MODEM ttyI1: COMID
May  8 11:33:27 comsurv FaxGetty[13908]: <-- [5:ATH0\r]
May  8 11:33:27 comsurv scanmails[14081]: execution started
May  8 11:33:27 comsurv FaxGetty[13908]: --> [10:NO CARRIER]
May  8 11:33:27 comsurv FaxGetty[13908]: MODEM No carrier
May  8 11:33:27 comsurv FaxGetty[13908]: MODEM set DTR OFF
May  8 11:33:27 comsurv FaxGetty[13908]: MODEM set DTR OFF
May  8 11:33:27 comsurv FaxGetty[13908]: DELAY 75 ms
May  8 11:33:27 comsurv FaxGetty[13908]: MODEM set DTR ON
May  8 11:33:27 comsurv FaxGetty[13908]: DELAY 2600 ms
May  8 11:33:27 comsurv scanmails[14198]: terminating
May  8 11:33:29 comsurv FaxGetty[13908]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
May  8 11:33:29 comsurv FaxGetty[13908]: MODEM flush i/o
May  8 11:33:29 comsurv FaxGetty[13908]: <-- [4:ATZ\r]
....


************* and the ../hylafax/log..

May 08 11:31:52.83: [13908]: SESSION BEGIN 00000010 492534xxxxx
May 08 11:31:52.83: [13908]: HylaFAX (tm) Version 4.1.2
May 08 11:31:52.83: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output dis
abled
May 08 11:31:52.83: [13908]: <-- [4:ATA\r]
May 08 11:31:57.95: [13908]: --> [7:CONNECT]
May 08 11:31:57.96: [13908]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyI1'
May 08 11:31:57.96: [13908]: STATE CHANGE: ANSWERING -> RECEIVING
May 08 11:31:57.96: [13908]: MODEM input buffering enabled
May 08 11:31:57.96: [13908]: RECV FAX: begin
May 08 11:31:57.96: [13908]: MODEM input buffering disabled
May 08 11:31:57.96: [13908]: <-- HDLC<23:FF C0 02 0E B6 86 D6 76 F6 42 04 04 04
04 04 04 04 04 04 04 04 04 04>
May 08 11:31:57.96: [13908]: <-- data [23]
May 08 11:31:57.96: [13908]: <-- data [2]
May 08 11:31:57.99: [13908]: --> [7:CONNECT]
May 08 11:31:57.99: [13908]: <-- HDLC<10:FF C8 01 00 73 5F 01 79 03 C0>
May 08 11:31:57.99: [13908]: <-- data [10]
May 08 11:31:57.99: [13908]: <-- data [2]
May 08 11:31:59.09: [13908]: --> [2:OK]
May 08 11:31:59.09: [13908]: <-- [9:AT+FRH=3\r]
May 08 11:31:59.37: [13908]: --> [7:CONNECT]
May 08 11:32:01.00: [13908]: --> HDLC<25:FF C0 C2 4C EC 4C AC 6C 04 2C CC AC 4C
04 9C 2C D4 04 04 04 04 04 04 FA C4>
May 08 11:32:01.00: [13908]: --> [2:OK]
May 08 11:32:01.00: [13908]: REMOTE TSI "+49 2534 xxxxx"
May 08 11:32:01.00: [13908]: <-- [9:AT+FRH=3\r]
May 08 11:32:01.01: [13908]: --> [7:CONNECT]
May 08 11:32:01.32: [13908]: --> HDLC<11:FF C8 C1 00 62 15 01 01 00 4E F3>
May 08 11:32:01.32: [13908]: --> [2:OK]
May 08 11:32:01.32: [13908]: REMOTE wants 9600 bit/s
May 08 11:32:01.32: [13908]: REMOTE wants page width 1728 pixels in 215 mm
May 08 11:32:01.32: [13908]: REMOTE wants unlimited page length
May 08 11:32:01.32: [13908]: REMOTE wants 7.7 line/mm
May 08 11:32:01.32: [13908]: REMOTE wants 1-D MR
May 08 11:32:01.32: [13908]: RECV training at v.29 9600 bit/s
May 08 11:32:01.32: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output gen
erated
May 08 11:32:01.32: [13908]: <-- [10:AT+FRM=96\r]
May 08 11:32:01.68: [13908]: --> [7:CONNECT]
May 08 11:32:03.28: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis
abled
May 08 11:32:03.28: [13908]: RECV: TCF 1915 bytes, 5% non-zero, 1808 zero-run
May 08 11:32:03.28: [13908]: --> [10:NO CARRIER]
May 08 11:32:03.28: [13908]: DELAY 75 ms
May 08 11:32:03.36: [13908]: TRAINING succeeded
May 08 11:32:03.36: [13908]: ACCEPT TSI "+49 2534 xxxxx"
May 08 11:32:03.37: [13908]: <-- [9:AT+FTH=3\r]
May 08 11:32:04.99: [13908]: --> [7:CONNECT]
May 08 11:32:04.99: [13908]: <-- HDLC<3:FF C8 21>
May 08 11:32:04.99: [13908]: <-- data [3]
May 08 11:32:04.99: [13908]: <-- data [2]
May 08 11:32:05.25: [13908]: --> [2:OK]
May 08 11:32:05.25: [13908]: MODEM input buffering enabled
May 08 11:32:05.25: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen
erated
May 08 11:32:05.25: [13908]: <-- [10:AT+FRM=96\r]
May 08 11:32:05.85: [13908]: --> [7:CONNECT]
May 08 11:32:05.85: [13908]: RECV: begin page
May 08 11:33:20.22: [13908]: RECV: 2312 total lines, 0 bad lines, 0 consecutive
bad lines
May 08 11:33:20.22: [13908]: RECV: end page
May 08 11:33:20.22: [13908]: --> [10:NO CARRIER]
May 08 11:33:20.22: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis
abled
May 08 11:33:20.22: [13908]: MODEM input buffering disabled
May 08 11:33:20.22: [13908]: <-- [9:AT+FRH=3\r]
May 08 11:33:20.36: [13908]: --> [7:CONNECT]
May 08 11:33:21.40: [13908]: --> HDLC<5:FF C8 F2 AC A0>
May 08 11:33:21.40: [13908]: --> [2:OK]
May 08 11:33:21.40: [13908]: RECV recv MPS (more pages, same document)
May 08 11:33:21.40: [13908]: DELAY 75 ms
May 08 11:33:21.48: [13908]: <-- [9:AT+FTH=3\r]
May 08 11:33:21.48: [13908]: --> [10:NO CARRIER]
May 08 11:33:21.48: [13908]: RECV send MCF (message confirmation)
May 08 11:33:21.48: [13908]: RECV FAX (00000010): from +49 2534 xxxxx, page 1 in
 1:18, INF, 7.7 line/mm, 1-D MR, 9600 bit/s
May 08 11:33:21.48: [13908]: MODEM input buffering enabled
May 08 11:33:21.48: [13908]: MODEM set XON/XOFF/FLUSH: input ignored, output gen
erated
May 08 11:33:21.48: [13908]: <-- [10:AT+FRM=96\r]
May 08 11:33:25.07: [13908]: --> [7:FCERROR]
May 08 11:33:25.07: [13908]: MODEM set XON/XOFF/DRAIN: input ignored, output dis
abled
May 08 11:33:25.07: [13908]: MODEM input buffering disabled
May 08 11:33:25.07: [13908]: RECV FAX (00000010): recvq/fax00007.tif from +49 25
34 xxxxx, route to <unspecified>, 1 pages in 1:28
May 08 11:33:25.07: [13908]: RECV FAX: T.30 T2 timeout, expected page not receiv
ed
May 08 11:33:25.07: [13908]: <-- [9:AT+FTH=3\r]
May 08 11:33:26.70: [13908]: --> [7:CONNECT]
May 08 11:33:26.70: [13908]: <-- HDLC<3:FF C8 5F>
May 08 11:33:26.70: [13908]: <-- data [3]
May 08 11:33:26.70: [13908]: <-- data [2]
May 08 11:33:26.96: [13908]: --> [2:OK]
May 08 11:33:26.96: [13908]: MODEM input buffering enabled
May 08 11:33:26.96: [13908]: RECV FAX (00000010): session with +49 2534 xxxxx te
rminated abnormally: T.30 T2 timeout, expected page not received
May 08 11:33:26.96: [13908]: RECV FAX: bin/faxrcvd "recvq/fax00007.tif" "ttyI1"
"00000010" "T.30 T2 timeout, expected page not received" "CALLER NUMBER: 26" "CA
LLER NUMBER: 26"
May 08 11:33:27.03: [13908]: RECV FAX: end
May 08 11:33:27.03: [13908]: SESSION END








____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
Follow-Ups:
- Re: [hylafax-users] faxgetty:problems with multipage documents and sedlbauer speedfax pci class 1
  - From: Lee Howard
Prev by Date: Re: [hylafax-users] Logfile analyzer
Next by Date: [hylafax-users] sending faxes => lines are missing - Part 2
Previous by thread: Re: [hylafax-users] Logfile analyzer
Next by thread: Re: [hylafax-users] faxgetty:problems with multipage documents and sedlbauer speedfax pci class 1
Index(es):
- Main
- Thread
Report any problems to webmaster@hylafax.org

HylaFAX is a trademark of Silicon Graphics Corporation.
Internet connectivity for hylafax.org is provided by:
VirtuALL Private Host Services