Re: [hylafax-users] sending faxes => lines are missing

[Gerd Müller <gmueller@it4sport.de>]

Hi Pedro,

no, that's what I forgot: It is class 2.0 :

Gerd

ModemType: Class2.0 # use this to supply a hint
ModemFlowControl: xonxoff # XON/XOFF flow control assumed
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
ModemNoFlowCmd: AT&H0 # disable flow control cmd
ModemHardFlowCmd: AT&H3 # hardware flow control cmd
ModemSoftFlowCmd: AT&H4 # software flow control cmd
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: "" # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC # set modem capabilities command
Class2DISCmd: AT+FIS # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control command


----- Original Message -----
From: "Pedro Rocadas" <procadas@yahoo.com>
To: <hylafax-users@hylafax.org>
Sent: Wednesday, May 08, 2002 1:16 AM
Subject: Re: [hylafax-users] sending faxes => lines are missing


> I didn't make any search in the mailling list about
> anything related about missing lines but, do you
> configured the modem in Class1?
>
> --- Gerd_Müller <gmueller@it4sport.de> wrote:
> > Hi all,
> >
> > when I send an ascii-file with "sendfax -n -D -d
> > 12345 foo". I recieve the
> > fax on the otherside but about every third line is
> > missing. I use HylaFAX
> > 4.1.1 under Debian and "MODEM ZYXEL Omni56K/1.09".
> > And my flow control is
> > right (I checked it a few times).
> >
> > Receiving faxes works without any problems.
> >
> > Has anybody any ideas?
> >
> > Thank you
> >
> > Gerd
> >
> >
> >
> > ____________________ HylaFAX(tm) Users Mailing List
> > _______________________
> >   To subscribe/unsubscribe, click
> > http://lists.hylafax.org/cgi-bin/lsg2.cgi
> >  On UNIX: mail -s unsubscribe
> > hylafax-users-request@hylafax.org < /dev/null
> >
>
>
> __________________________________________________
> Do You Yahoo!?
> Yahoo! Health - your guide to health and wellness
> http://health.yahoo.com
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
>   To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
/dev/null
>
>
>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null