Hylafax Mailing List Archives
|
[Date Prev][Date Next][Thread Prev][Thread Next]
[Date Index]
[Thread Index]
GVC Modem
Hi,
when I learnd about hylafax some days ago, I was so excited I had
to ftp it at once. I think it's a great piece of SW!
Compiling, installing and configuring was a smooth thing, alas
I encountered a problem with my (prehistorian) GVC Modem (Fax V.27ter,
V.29).
Here is the log:
===> cut here
7653]: SESSION BEGIN 00000005 492273910022
7653]: SEND FAX: JOB 2 DEST 910022 COMMID 00000005
7653]: DELAY 2600 ms
7653]: <-- [15:ATE0V1Q0S0=0H0\r]
7653]: --> [14:ATE0V1Q0S0=0H0]
7653]: --> [2:OK]
7653]: <-- [21:ATS8=2S7=60\Q3&D3&C1\r]
7653]: --> [2:OK]
7653]: <-- [12:AT+FCLASS=2\r]
7653]: --> [2:OK]
7653]: <-- [10:AT+FTBC=0\r]
7653]: --> [5:ERROR]
7653]: MODEM Command error
7653]: <-- [10:AT+FBOR=0\r]
7653]: --> [2:OK]
7653]: <-- [13:AT+FPHCTO=30\r]
7653]: --> [5:ERROR]
7653]: MODEM Command error
7653]: <-- [24:AT+FDCC=1,3,2,2,2,0,0,0\r]
7653]: --> [2:OK]
7653]: <-- [5:ATM0\r]
7653]: --> [2:OK]
7653]: <-- [12:AT+FCLASS=2\r]
7653]: --> [2:OK]
7653]: <-- [10:AT+FTBC=0\r]
7653]: --> [5:ERROR]
7653]: MODEM Command error
7653]: <-- [10:AT+FBOR=0\r]
7653]: --> [2:OK]
7653]: <-- [13:AT+FPHCTO=30\r]
7653]: --> [5:ERROR]
7653]: MODEM Command error
7653]: <-- [24:AT+FDCC=1,3,2,2,2,0,0,0\r]
7653]: --> [2:OK]
7653]: <-- [24:AT+FLID="+492273910022"\r]
7653]: --> [2:OK]
7653]: DIAL 910022
7653]: <-- [11:ATDT910022\r]
7653]: --> [3:CED]
7653]: --> [5:+FCON]
7653]: --> [30:+FNSF:AD 00 36 40 80 28 01 E4 ]
7653]: REMOTE NSF "AD 00 36 40 80 28 01 E4"
7653]: --> [26:+FCSI: +49 2273 910022]
7653]: REMOTE CSI "+49 2273 910022"
7653]: --> [21:+FDIS:1,3,0,2,0,0,0,4]
7653]: --> [2:OK]
7653]: REMOTE best rate 9600 bit/s
7653]: REMOTE max page width 1728 pixels in 215 mm
7653]: REMOTE max unlimited page length
7653]: REMOTE best vres 7.7 line/mm
7653]: REMOTE best format 1-D MR
7653]: REMOTE best 20 ms, 10 ms/scanline
7653]: USE 9600 bit/s
7653]: USE 20 ms, 10 ms/scanline
7653]: SEND file "docq/doc2.ps;30"
7653]: Modem does not support document page width, max page width 2432 pixels, image width 1686 pixels
7653]: <-- [5:ATH0\r]
7653]: --> [9:+FHNG: 40]
7653]: REMOTE HANGUP: Unspecified Transmit Phase C error (code 40)
7653]: --> [2:OK]
7653]: SESSION END
===> cut here
Here is my config.cua1:
===> cut here
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class2 # use class 1 interface
ModemRate: 38400 # locked for fax sending&receiving
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT\Q0 # disable flow control cmd
ModemSoftFlowCmd: AT\Q1 # software flow control cmd
ModemHardFlowCmd: AT\Q3 # hardware flow control cmd
ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C1 # DCD follows carrier
ModemSetupAACmd: AT+FAA=1 # enable adaptive-answer in Class 2
#
ModemRecvFillOrder: MSB2LSB # bit order of received facsimile
ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
ModemDialCmd: ATDT%s # T for tone dialing
#
# Chip locks the line rate and switches to xon/xoff flow
# control when receiving facsimile--we must follow suit.
#
ModemAnswerFaxBeginCmd: "<19200><xon>" # lock line rate & switch flow control
#
Class2RecvDataTrigger: "\022" # character sent to modem to start recv
#Class2DDISCmd: AT+FDIS # set parameter before dialing
===> cut here
I use hylafax with Linux 2.0. The modem worked fine for outgoing
faxes with mgetty.
Any idea what the problem could be?
Many thanks in advance, Reinhard
--
We've arranged a global civilization in which most crucial elements
profoundly depend on science and technology. We have also arranged
things so that almost no one understands science and technology.
This is a prescription for disaster. C. Sagan